If review for IJOY Vape Captain Kit Mercury coils

IJOY Captain Kit come in various colors.

– Mirror rainbow
– Mirror black
– Mirror Green
– Mirror Gold
– Violet Mirror
– Bronze mirror
– Art Mirror
– Mirror black
– Mirror Red
– morror blue
– Mirror Orange

Specification:

Baby vindictive IJOY MOD

– Size: 66 x 48 x 34 mm
– Maximum power: 108W
– Output Mode: VW / VT (Ni / Ti / SS) / TCR Fashion
– Resistance Range: 0:05 – 3.0ohm
– Voice control system: English
– Battery Type: 2 x 20350 batteries (included)
– Double battery capacity: 2800mAh
– Topic: About 510

diamond baby tank IJOY

– Size: 52.7 x 22.5 mm
– Capacity: 2 ml (TPD Version) / 4 ml (standard)
– coil: DMB-mesh 0.18ohm coil (preinstalled 40-80W)
0.15ohm coil DMB-DM (40-80W)
– advanced resin drops 510 Drip Tip
– Subject: 510

 

features:

– Dual Power 108W battery 20350 Max
– the smallest voice control TC 108W MOD in the market for e-cig
– an innovative voice control
adjustable LED light button RBG –
– large color display OLED 1.3 inch
– The only way the custom user
– Firmware update
– There is nothing wrong with the tank 30 mm
– 180 ° fast charge with a screw cap 2 ml / 4-E juice ml capacity
– Mesh DMB DMB new coil and coil DM adamantine
– adjustable air flow

In the frame:

– Baby Safety IJOY MOD Avenger
– 2 x 20350 batteries
– 4 ml baby diamond deposit
– DMB-Mesh 0.18ohm coil (40-80W I preinstalled)
– coil DMB-DM 0.15ohm (40-80W)
– The changes in the glass tube (2 ml)
– USB Cable
– Free
– Warranty card

IJOY JUPITER is available in several different colors. I received this black tank,

diameter diamond baby tank 22.5mm, height is 52.7mm. The build quality is good, no quality problems. We can see the atoizer statue, at the bottom, you can see engraved “Designed by IJOY” and “baby tank diamonds” on the upper deck, you can see engraved “IJOY” and diamond engraving. Below the upper limit, you can see some details and the details of the air flow control the same diamond ring.

 

Diamond beautiful baby tank with a decrease in resin 510 point drop is very pretty at the top of the tank in my opinion. You can also use your own suggestions 510 drops here without any problems. Drip Tip almost comfortable to use. Drip tip diameter is 13 mm, the tip diameter of the droplets is 8 mm.

This is a filler spray top and can remove the top cover is very easy, just half a turn is needed and that is, you can fill the tank without problems, two details recorded on the upper deck of much help when you want open the top cover. A statement from the top, you can see a large hole for the liquid mail, so probably will not be a problem, even with a large bottle. In my opinion it is a very good filling.

Baby diamond comes with a glass bubble tank, this tank has a capacity of 4 ml, which is very good for a small atomiser. glass bubble tank color, may be able to view photos. Aerosolization receive ordinary glass tank in the package, the tank capacity is 2 ml regular glasses. I use a glass bubble because I like how it looks and I like the ability.

With diamond tank will receive two different rolls, which comes preinstalled with DMB – M5 coil, the coil backup is receiving DMB – DM. The second coil is a coil, mesh force recommended DMB – M5 is 40-80 watts coil, coil resistance is 0.18ohm, DMB recommended concentration – DM is 40-80 watts coil and coil resistance ohm 0.15 .
As always, before you meet the needs of special coil tank with a few drops of liquid E then you can fill the tank and spray immediately and took avoided.
You can also use fewer rolls:

DMB – coil C1, 0.3ohm coil resistance, suggested to 35-70W
DMB – coil C2, 0.2ohm coil resistance, the force suggested 40-80w
DMB – MS coil, the coil resistance 0.18ohm, suggested force 40-80w

Deeper in the field where you have to push the batteries are good and you can change the coil without any problems. The bottom of the tank, you can see the gold plated wire-pin 510 is also good here.
Basically, you can see the control ring in the air flow and the air flow ring can see two vents. perfectly tensioned ring airflow and can adjust the air flow uniformly seated on one side, the same on the other side.

How does this work tank:

It is very simple tank sub-ohm, which I like. It is very easy to use, easy to fill the tank is easy to alter the coil atomizing or removed for cleaning. I like drip tip, looks great in my opinion. good build quality, no sharp or bad engine.The IJOY Diamond coils have worked well without rap, no leakage, eg using 70-30 pg and liquid. fairly good flavor to a tank sub-ohms, steam production is good also.

I have no problem with the coil, both M5 and dm work very well, but I like the coil more comfortable M5. DM coil is longer, but tastes better when the coil is used M5, at the least that’s my opinion, you may want to last DM coil. Anyway, this is also built under the deposit ohms and working properly, so I can not pick anything wrong.

 

IJOY Shogun Kit

Avenger is a new baby mod mod with IJOY has voice control. It has control over the previous year and the second is smaller. 48 mm x 34 mm x 66 mm. Mod Size The maximum power that can be used at 108 watts mod. resistance of the coil is used here 0.05omh-3ohm. The build quality is good and you can feel the quality when held in hand, I can say that this model is quite a lot of weight. Avenger infants fed by a battery 20 350 double. It can be used in several different ways, it can be used in the power mode, fashion tc (or art, which, m1, m2), TCR mode and housing. I have to say I really IJOY always offer the battery in your mods very well with this device, two batteries received 20 350 and no need to buy batteries separately, you can use the device immediately. IJOY 20350 battery has a capacity of 1400mAh, so it basically has a capacity of 2800mAh mod, but also the battery, you can see, says a maximum current of 25 amps.

From the top you can see the relationship stainless steel chaotic, good, good boy mod, a gold plated pin 510 and spring. In this unit, using atomizers with a diameter up to 30 mm without being false.
The Defense Department can see some detail on the back of the unit, there is a “baby Avenger” on the front of the device, is “IJOY” at the bottom of the mod, you can see the “Designed by IJOY” . From the back of the room, you can see the battery cover and there are 8 ventilation. The doors have played a little when you when you have the battery open the door, but the mod no sound when the device is shaken, the battery is still done a very nice place when the battery and can not be opened for the occasion . When you open the battery cover, you can see the orientation of the recorded battery, but engraved in black, which can be a bit silly, it will be marked white.
the shutter button on the device is placed in the MoD and the buttons on the side of the dislocation fire and works very well. the shutter button is placed in my opinion, in a very good position and can be used especially with a finger or hand, you can not miss when the mod is taken and want to delete.
From the front of the device you can see the screen and under the keys and a USB port for charging and updates.
avenger load balancing support IJOY baby so you can load here, but as usual, I recommend using an external charger. Button on the front also the dislocation and sensitive. While LED light touch and if the light is on, the lights plus and minus buttons zone.
This device has a color screen, the screen size of 1.3 inches, the screen is very good in my opinion, on the screen, you can see the combination of red and white and you can not change the color on the screen .

To activate it you must click five times on the fire button and turn it off, you have to click the shutter button 5 times. When the screen is on, you’ll see the version of the firmware, but when eaten in the display mode, see:

– Power
– blow
– hot
– coil resistance
– Volt
– double the battery indicator

To enter the menu you must click 3 times on the shutter button, take a look at the menu:

– Supply Mode
– Pod Mode
– LED
– Climate Control
– RCT
– Together

To move, use the plus and minus button and enter the submenu, use the shutter button. Power mode can be adjusted before the heat and can be selected for fresh, normal and hard preheating. If you choose regular heat before still provide warmth before and will go to the point of power. It may be inconvenient for some people, so quickly, but the fire, which could be inconvenient for someone who wants to use it without her.
If you select a gondola, which is here to adjust the power output in volts, which is a very good choice and I like, can adjsut between 2.5V-3.8V that.
If you choose the LED on the menu, you can choose the color of the LED lights and can choose how red, green, blue, white, colorful voice. The sound mode is an interesting choice of light. So if you want your LED lights mod, you can play with and choose what seems best for you, if you do not, you can always disable the selection of LED lights.

Then comes the TC mode, here is an EN, IT, SS, M1, M2. Menu following TCR and is the preferred game. Can then restore the breath against the blows of the same device when the battery is removed remembered, but a counter is reset when swollen puffs 9999 is pressed. You can also set a screen, you have several options, 30, 60, 90, 120 s. Finally, you can do here is to enable or disable voice control. Given that the voice command is the main feature of this mod, I will write comands voice here. Anyway, the voice control function can be very interesting for someone. So when you want to use voice control to say “Hello IJOY” and you will see a microphone at the bottom of the screen. Here we have a sound check at the previous event.

Voice commands:

– Hello IJOY
– Soft mode
– Normal mode
– Hard Mode
– Locking device
– activation device
– High tension
– Twenty watts
– Thirty watts
– Forty Watt
– Fifty watts
– The sixty watts
– Seventy watt
– Eighty watts
– Eighty watts
– Low battery
– Auto watts
– Turn on the light
– Light music
– light

 

I used this option, but it may interest you. Cource tried and works well, but if this option is used, it should be in a quiet environment, otherwise do not understand.
It can also lock the device by pressing plus and minus buttons, similar to the output.

 

How vindictive baby mod:

Let me start with the battery, the new battery, I can not find much information about the battery, battery, said 25A and 1400mAh. Because I want to IJOY Mercury Vape, I tested the battery with the 1.15ohm coil 12w, average 2.5-3s blow. This means about 460 flashes to indicate when mod indicates that the battery is empty.

the build quality of the model is good, works well and I use it every day without any problem, all you can interrupt a normal person hot pre cousin if a shot is set regularly before your new give a warm and I hope fixing him with updates,

better voice control, which is great if you want to control the use of sound, can be useful for you. lights here, have also led, one would like LED lights, not a person, but can be disabled if they do not like.

It is a very short mod and I felt very comfortable in the hand, in the opinion of my shutter button in the perfect position and I love it.

I love how the appearance of the machine basically works well, the control works great voice and I recommend this mod for people who want to try a voice command for you.

 

 

You can buy it here: IJOY.

Comment on the Smok tanks Nord pods RPM Pro mag grip trinity alpha nfix

I received a kit Morph smok nord2 pods the purposes of this review.

Smok morphing color:

– Black gold
– 7 colors and black
– Red Black
– Blue and Black Prisma
– black and chrome prism

Description and features:

– Morph Mod 219 size – 44.8mm x 30.2mm x 84.5mm
– Battery Type: 18650 dual battery (not included)
– Power range: 1 W-219W
– Display: touch screen 1.9 ”
– Input voltage: 6.4V 8.4V-
– Output voltage: 0.5V-8.2V
– Cooking time: 0.001s
– Charging Current: 1.8A
– Charging voltage: 5V
– Resistance Range: 0.1-2.5ohm (VW) /0.05-2.0ohm (TC)
– Temperature: 200-600 ℉ / ℃ 100-315
TF tank size -: 25.5 mm x 56 mm
– Tank capacity: 6 ml
– Discussions: Discussions 510

In the frame:

– Morph SMOK RPM 80 Pro

– 6 ml Smok tank TF

– Smok TF BF-Mesh 0.25ohm tank coil (pre-installed)

– 0.25ohm Smok TF BF-Mesh tank coil

– silicone protective glass bulb

– glass tubes Replacedment

– USB Cable

– User’s Guide

– Bedrooms

 

Smok tank tf:

 

Tf is 56 ohm smok mag grip mm high and is 25.5mm in diameter.

In the package with the atomizer you will receive a glass tank and tank flat glass bubbles were very good, also received a glass tank silicone protective and two coils. atomizer good quality of construction, the cable is good and everything is as it should be. Previously you could see atomizer “Smok” and the bottom of the atomizer atomizer can see “Designed by Smok”, you can buy 5 different colors.

Atomizer equipped with a drip edge 510 pre-installed, so that the atomizer can be used other end 510 reduction if it did. Drop by drop-off points are pre installed very nice and I think it is convenient to use. I think it’s great that finally made the atomizer 510 is supported, but for some people would be better than the atomizer is compatible with 810 drip tips, however, advanced packaging drops are very comfortable and good looking.

This is a high-filling syringes. Before you can see the key press atomizer to install. When the top cover is pressed, you can view the contents of the hole. Comply with large holes and the atomizer can be filled without problems, so basically, filling here is very simple and can be filled atomizer very fast. More filling works well and should not leak when a sprinkler system is required.
glass syringes fitted with a bubble tank and pre-installed on the box will receive the usual glass tank. atomizer tank with a capacity of ordinary glass is a tank capacity of glass bubbles 2 ml and 6 ml capacity is very good and I think many people like reservoir capacity. With the atomizer receive a silicone protective glass for the tank to protect the tank in case you drop, very good in my opinion.

Using the spraying which receives two rollers and two coils of the same. Bf mesh coil is coil and its 0.25ohm resistance, it is recommended to power the coil is 30-80w 60-70w and better jobs. It can be very easy to change the coil atomizer, you have to do is press the atomizer coil is very easy and simple. When the coil is used first, it must be primed with a few drops and can be inserted into the atomizer and filled syringe.

Basically, you can see the ring control air flow and the ring can be seen two slots airflow. ring control air flow, which has some details that helps when you want to adjust the air flow, so you can more easily adjust more or airflow and allows you to leave out is the same side Oher.

How does it work? Atomizer and my mind:

build quality of the atomizer is very good, everything is as it should be. It comes with sophisticated drops 510 installed very good because it can use a spray tip 510 drops. Falling drop that comes pre-installed my opinion is comfortable to use. 810 atomzier be more compatible with drops of advice, so this could be a disadvantage for some people. The system is very easy to complete and can fill up fast, so far, works well. The capacity of the container is 2 ml glass standard, but with a very good bubble tank capacity glass capacity of 6 ml. In this package, we received a silicone protector for your tank that was really good. You really can easily replace the spool into the atomizer and the atomizer, you receive two coils. Atomzier work very good, taste good and also steam, this is not the best there is a detection coil is certainly better than many who have tried to mesh aerosols, but. Therefore, the deposit is tf solid deposits in ohms, it worked well and was very easy to use.

Drawbacks:

 

– Not compatible with 810 drip tips

 

 

 

Pro:

 

– The build quality is good

– easy to fill

– Compatible with 510 drip points

– comfortable drop points fall preinstalled

– 6 ml capacity tank bubbles

– Protective silicone

– The good taste

– Two coils in the package

– Easy to replace the coil

smok trinity alpha tank is powered by two batteries 18650 and this model works 1-219w. You can buy this model in 5 different colors.

This model is 44.8mm x 84.5mm x 30.2mm dimensions are. mod good build quality, everything is as it should be. This mod design is very good in my opinion, received a blue mod and you can tell the beautiful paintings. The device is very comfortable to use, with no sharp edges and large shutter button, because it feels very nice in the hand. Faced with this mod you can see “Smok” and behind the mod, you can see the “Morph”. This model has a touch screen that I really like and also supports multiple modes mod that can be used.
From the top you can see the connection mod and here we have a spring pin gold plated. Put here well and I had no problems with atomizers I speak here. Good connections, which rose slightly, which is good because you do not scratch the Ministry of Defense with atomizers. In this mod, you can use the aerosol up to 26 mm, which is more than was good for me.

Under the mod you can see the battery cover. I really like the battery cover locking mechanism. When the battery cover is open, you can see how the mod mod painting batteries and is powered by two batteries 18650. So far I have not had a problem with the battery cover. When the battery mod mod noise and when there is a good rattle.

 

On one side of the mod, you can see the shutter button. The trigger is great and really the trigger. shutter button is very convenient to use, is a dislocation and works very well. At the top you can see the shutter button and a button using this button, you can lock the screen or off screen. When you press the screen lock button and the click of a button, you can turn off the screen.

 

In front of the mod, you can see the screen and USB.
You can use the USB port for software updates or to charge half the load balancer, but as usual, I recommend to recharge the batteries in an external charger.
In this device, we have a color display screen is excellent, large, the size of the screen is the 1.9inch screen and in my opinion, this device looks very nice and it was really the touch screen.

To activate it, you must click the trigger five times and had to do the same to turn it off. When the device is in power screen mode, you’ll see:

– I can not
– locking / unlocking
– Time Hojaldre
– W
– Heat
– Left and right
– Resistance
– V
– against cerebrovascular accidents
– AN
– The battery indicator

The touch screen works well and so far I have not had a problem with the display. Also on display, you can see everything nice and a very good screen brightness.
Enter in the menu, you can see:

– Modus
– My Style
– Hojaldre
– Set

When the mode is selected, you can choose different modes:

– Watt
– temperature Ti
– Temperature Ni
– Temperature Ss

If you choose me mode, you can set up four different operating modes, and you can adjust your diet, you can pre-heat and add liquid name and network cards.
If you choose Puff Puff, you can rearrange the tables.
You can see the set included:
– General (of the factory, accessibility, food)
– Chip (Info)
– topics
– Access codes

 

If you choose a theme, you can choose a different background and you can choose different colors on the screen and can also set the screen timeout. If you choose an access code, you can set your own password, the device asks every time the battery is placed in a mod.

 

How do these devices work and my thoughts:

smok nfix pods is very good in my opinion, and certainly one of the best mods out there,

I really like the color blue. mod good quality construction and complain about this mod. Chateo also looks good, but I have to say that this magnet fingerprints mod will be a loss for someone. In the device it can be used for a diameter of 26 mm without good atomziers projection. You really can be easy to put the battery in the Ministry of Defense and the extent to DIND’T have a problem with the battery cover. Rattle nothing when shaken battery and when morning. large shutter button and I really like the type of shutter button. It works well and dislocation. It’s also good to have a key to lock / unlock the screen and enable / disable screen. This model also supports load balancing, but as always recommended to charge your batteries in an external charger. Really beautiful screen and on the screen, we have all the information we need, big screen, the screen brightness is good and works well. I also like that we can change the color of the screen. This device has many options yet very easy to use. Mod works very well if you ask me, I tried with my MTL and atomizers me and runs smoothly DTL and will probably continue to use the device every day. If you are considering buying this mod and mod design you want, I can tell you all that this camera can be obtained safely.

 

deficiency:

– fingerprint magnet

 

Pro:

– Good build quality
– Good design
– Jack Good
– it can be used up to 26 mm diameter without false atomizers
– Binding slightly
– comfortable to use
– cozy fire button
– Screen Buttons
– a beautiful and big screen
– a good screen brightness
– Much of the information on the screen
– Easy to use
– The screen works well
– Theme Options
– balanced load
– the battery cover is working well
– My selection method
– Password Option
– No ring

 

sourcemore thanks
You can buy the kit here: Smok complete Morph

You can buy tanks: smok tanks

Uwell Caliburn KOKO nunchaku Crown Pod Caliburn Pods amulet Crown 4 review

Well I received a Caliburn KOKO the purposes of this review.

 

Well nunchaku is available in several colors:

 

– Green Metallic

– iridescent

– Purple

– Black and Gold

– The corrosion of iron

– Black Full

– Sapphire Blue

 

Description and features:

 

– Size: 27.4 mm x 94.5 mm

– Material: Stainless Steel

– Power range: 5-80W

– Resistance range: 0.1 ~ 3 ohms (VW), 0.1 ~ 1 ohm (TC), 0.1 ~ 0.5ohm (manual)

– Temperature range: 100 ~ 300 ° C / 200 ~ 600’F

– A new generation of E-cigarette panel Well Control, making boxes mod tube insurance

– Operating mode: the power mode, the mode TC (NI, SS), the bypass mode

– Battery 18650

– Ergonomic design felt perfectly at hand

– Pocket size when traveling

– simple interaction system

– Micro USB port for charging

 

 

In the frame:

 

Crown 4 uwell

– USB Cable

– Warning Card

– User’s Guide

 

Well Uwell Crown Pod, powered by a battery and 18650 can operate up to 80W. In the widest part of the diameter 27.4MM mod is the height of the model is 94.5mm, but on top of the diameter is 25 mm mod. Nunchaku is not a big tube mod mod in my opinion, it has the perfect dimensions and mod is very comfortable to wear, feels good in the hand because of the way. Nunchaku are made of stainless steel and feels very solid, the build quality is excellent and I can not complain about anything here. color quality so far looks good so I do not see scratches on the mod mod and I use that a lot. You can buy this model in several different colors, 7 colors, black. In the Caliburn Pods, you can see the details, from the top of the mod, you can see sculptures in the tube that you can see engraved “nunchaku Well”. At the top of the battery, you can see some details that help in removing the battery cover and at the bottom you can see engraved “Well Designed by”, “www.myuwell.com” and you can see the stars recorded. Personally, I think the beautiful mod, but this is very subjective.

From the top of mod, no connection with stainless steel spring loaded pin plating and thread here either. As have been said above a diameter of 25 mm, can be used here sprayers anything up to 25 mm without false.

Sub mod, you can see the battery cover, the battery cover also has a good thread and can tighten or loosen the mod smoothly. In the battery cover, you can see four vents. A getting out of the battery cover, it may be reduced pin and spring pin. Inside, there is a more mod pin and you can see very clearly marked with the red, so you know how to put on your battery. No it isolation mode, in which case the battery is used stripes, but do not use the battery if you notice any scratches on the battery.

In the tube, you can see the shutter button, the plus and minus buttons USB port and you can see the screen.

Here hold the fire button and it’s not hard to find in a mod when vape like, shutter button has several sculptures that can be felt under your finger. shutter button works fine, I have no problem with the shutter button it is very sensitive and dislocation. More and less boots work fine too and I have no problem, but when mod can stir here some keys rattle.

In the tube there is a USB port lets you charge your batteries in a mod, but as usual, we recommend using an external charger to charge the battery.

Basically, there is a very bright screen and the screen, you can see everything on the screen is very clear.

 

To activate the mod must click 5 times on the shutter button, the same is when you want to disable the mod. When the Ministry of Defense lights shown “Well Hello” on screen and after that if the power mode of the device is used on the screen, you will see:

 

– Power

– The battery indicator

– coil resistance

– Volt

 

 

If you use the device in temperature control mode, appears on the screen:

 

– Temperature

– The battery indicator

– coil resistance

– Power

 

To enter the menu you must click 3 times on the shutter button, the menu can be seen:

 

 

– Supply Mode

– Temperature Ni Mode

– Temperature Mode Ss

– Bypass Mode

– Return to factory settings

– Exit the menu

 

uwell amulet of 5-80watts when the key roughly 0.5W watts is pressed up or down, and 80W power when the plus button and the return to 5W is pressed when the power is on and press the button 5W reduced, go to 80W.

 

You can lock mod really, all you have to do is press the shutter button and the minus button, you will not be able to use the mod at all until you open it with keys and reducing fire. You can also block only plus and minus buttons, for this you need to press the shutter button and a button, so you can vape but you can not adjust the power until the device is opened.

 

 

 

 

MOD

 

 

the entire first mod is a very good shape and feels great in hand and if you ask me it is very convenient to use, it’s hard not to find the shutter button, as is and engraving, which is a additional advantage. I like the size of a mod, mod height of only 94.5mm, which is a big plus for me, because in combination with most sprayers will be very pleasant due to the high that I can take with me all mod. Mod has a very interesting feature, I can lock the device, in fact, I love it because there is no possibility that can be activated in the pocket, is really not a problem to switch off the device before putting it in a pocket, but it was good we had a key choice.

This model is powered by a 18650 battery and can not use other batteries here, not only can use air battery of this mod 20700.

This device works great, the fries were good and I did’t have problems, so far so good. I use the camera low power and high strength and can not complain, it works as it should. Atomizers in a suit 24mm or 25mm diameter well in the Ministry of Defense, of course, you can also use smaller sprayers with beauty rings.

build quality as I said very good, a good thread on top and that I will not be a problem when you want to put the battery in the mod. shutter button and the plus and minus buttons run smoothly.

Basically it is a very simple model to use, you can choose from four modes, so there’s nothing complicated here and you can customize almost everything quickly.

I recommend this mod for those who like to use them a tube mods, I think it is a very good mod and works as expected without problems so far.

 

 

 

Drawbacks:

 

– Can not use a 20700 battery

 

 

Pro:

 

– The build quality is good

– Very comfortable to use

– Mod simple, use

– good appearance (subjective)

– Good Button

– The screen is bright

– Chip works well

– The colors look good

 

 

You can get it here: Uwell

Smoant Pasito Replacement Vape and Charon Baby review

In summary and evaluation

Propel is a very good entry into the Smoant Pasito Vape Pod System And the best thing I’ve tasted to date, Replacement RBA Coil Head it even better. A reference that will take some beating – A must buy.

Ranking 9/10 – Game Changer
The highest value that can give because I do not believe in 10/10. Perfection is subjective.

POD / AIO / MOD ??? – opaque line
I put this in the category of the IOA, but technically can be classified tanks and drums MOD changes. Line with fuzzy pods evolution, leading to devices like Propel – Catfart calls for all I care! It is a compact spray device and I love the way the market is growing.

main feature
Propel feature-rich for such a small device, here are some of them:

content and the content of the box
Early on, you know you have something special; box is one of the best packages that I have seen used with magnetic flap folds to reveal a double, which in turn reveals Propel. Therefore, there is information printed on the flaps and housing with a USB cable C is accepted, the additional coil and some cards do not bother to read (but not).

Most impressive of all, even if it would be better if you include the RBA.

contents
1 x mod Propel
1 x cartridge Propel
1 x Ni-coil 80 MTL 1.4Ω
1 x DTL mesh coil 0.6Ω
Cable Type 1 x load C
± 1 x coil
Card 1 x Certificate
Warranty Card x 1
1 x User
First impression
A good first impression with the opening of containers, goods have Pasito! There is a nice little game is a solid, well designed, and the magnetic connection is made to remove and replace favorable winds. The style has met a mixed reception, which I personally like. Smoant the following claims:

“ROE INNOVATIVE TECHNOLOGY
CPR is used as a design material end product more beautiful and durable color. No fingerprint. “

grandma hand, I do not know CPR?

CPR?
printed colored resin?
urine reaction of cow?

My best guess is the second choice, but who knows? Additionally, Smoant Pasito II Pod Kit reacted and released a stylish addition to the carbon fiber should meet the enemy. Have time to be admired mod, I put it on charge faster and C friendly with USB cable. Then I begin the coil to the nacelle. He pulled out of the base, then simply unscrew the coil connector, very easy. Then I primed coil with a few drops of my favorite Nic juice Salt and screwed back and pushed together.

Propel does not ignore one of the most desirable features of an AIO, and the air flow adjusted. cursor a little uncomfortable at the top of the gondola is. MTL layer (the mouth of the lungs) and DTL (lung Direct). Although a little checklist to solve, are welcome features and benefits for me. Not the size of the smallest, but still compact and easy pocket either:

Features, comment and operating coil
On the one hand, a shutter button, control and port USB-C power. Interestingly voluntary shot button, which is unusual in the beginning, but I quickly got used to me. I find it easy to shoot some point waiting with fingers or thumb, a place that has never been highlighted “pockets of fire” and have high strength. Button 5 power settings to adjust the power level of fine disc, the power levels appropriate for me to lower, but they are heated to improve vaporiser:

Replacement MTL-Ni80 Coil Head.

Basically, there are many on the opposite side ventilation holes to empty the shutter button, the rear panel is simply a function without CPR. CPR before two separate panels, one on top of the light emitting diode 5 which is used for various functions:

power level – click on the desired improvement and see all the points of light accordingly.
Battery Status – press the shutter button five lights flash at full load and reduce the number of points are displayed as the battery level is reduced.
battery levels – Each point reflects the level of load: 20% – 40% – 60% – 80% – 100%
Pressing the shutter button five times to put the unit in standby and back 5 clicks.

That’s all there is to it, is very intuitive and easy to use. As mentioned above, the car has a magnetic connection and loosens easily but still adhere. Unleash hell and will probably remain in place.

“Pod” has a cartridge drops sliding properties to the end, which can be substituted with other suggestions Propel. boring is a commitment to meet the needs of MTL and DTL and to be honest, it was very good for both of them. There is a small plastic slider to control the flow of air, wide open to attract a tight DTL, MTL almost closed provide a very good draw.

battery life is very good and much better than expected with a battery of 1100 mAh, and the cost is also very fast, even at the price of 1 ampere. Which should last a day on moderate use.

roll
MTL: 1.4ohm coil Ni-80,
DTL: 0.6ohm DTL mesh coil,

Charon Baby Pod System Starter Kit

It may seem boring, but it’s pretty easy to get to the coils. Waiting on the bridge and prefolding legs to match the holes in the two positions. With the lower coil legs, the first entry is easy, but the second requires a little more attention, use only a small pair of pliers and insert the tip of the needle around. slightly lower threaded pin, not too tight, you have to throw the leg with forceps, and after being satisfied with the position that can tighten the screws (perhaps with coils 2.5 mm rod). This will damage the bit if the rod coil pinch and pull to remove the air flow and writing, then dried and pressed register shaped ceramic tweezers to remove the access point. Checking Ohm stability and no shorts (mine is 1.4 ohms), you are ready for the shaft.

Cut a strip of approximately 6 mm wide axis and remove the thin skin on both sides (also not remove) a loose roller, then press one end of the wire through the coil you. I found the strip through with some tension at both ends help maintain the coil shape. I had to survive with little resistance. If it is too tight, it will be examined more coils means that there is too much cotton. Cut to length, should reach just below the base, then slimmed down a little trick. Then, spindle and shaft juice (about 8 watts added pulse when the juice) and the foot when wet, should be comfortable in a circular groove Meta. Finally, screw in the manufacture of brand fireplace careful not to slip cotton yarn.

All that remains to do is remove the base 510 and the screws on the bottom of your rolls propulsion makes the job!

In the like many, but it took a few minutes total.

If you still are not sure then YouTube is your friend, find the “Pasito Smoant RBA.”

So installed Propel RBA coil cartridges, refilled and tested. Not expecting much, I was surprised how great frikkin taste, especially with my first weird construction! They smoant highlighted in R & D of the whole package. Although a large roll of values, just use RBA now my skills have improved with each generation, I really liked the development of RBA. It is much easier than many MTL RTA is mine.

conclusion
Well, if you’ve read this far (well done), you see I’m in love with these AIO devices, especially with outstanding RBA. I arrived at the advantages and disadvantages soon and I will fight with the inconvenience!

It would be better if they included the RBA, but, to be fair, for the price was an incredible deal and I appreciate all the love in the world, does not build its own coil that is understandable remove PVT RBA maintained.

I tried and many teeth and AIO Smoat Pasitio too, but in their own league and it will be a tough act to follow. And others to follow, and more devices RBA or a selection of nearby which is a positive development. “Fire and forget” pods still have their place and can see that the market is fragmented, but Pasito a reference and if the new device happier late! Meanwhile, I am more than satisfied.

I would buy it again if I lost or broke – I have an “alternative” and that the RBA buy 100% YES.

pros and cons
Pro
The first contact with the market.
Watt variable.
construction quality.
Magnetic ‘Pod’.
coil is a very good value.
Easy to use.
Packaging and presentation is the best I’ve seen.
RBA excellent choice.
The battery life.
fast charging.
USB-C
adjustable airflow.
easy filling.
Style (subjective).
Pocket friendly.
longe use.
Tank 3 ml (2 ml TPD).
Punctuation.
Cons … .. eh …….
Love or hate model.
RBA is not included.
More than most.
DTL little too tight.
I do not know what CPR.
the box was too good to throw away.
I thought I would give

Anthony Vapes: Advken Manta RTA Review

Hi all, Anthony woozy back here with my Advken Manta RTA. Warning: This product was sent to me from elementvape.com

 

comments Disclaimer

I review the products for what they do not take into account where it comes from or who made it. The results of the test results for what is in my hands. Due to possible differences QC your experience may be different. I spent more time with the product and then most of the criticism and try to be thorough, making disassembly to check faulty design, test accuracy, and stress testing, which is usually done in the ‘care industry to try to “force” the failure diagnosis or potential failure point to give me an idea of ​​the life of the product. That said, there is no way to predict whether or device will last 6 months, 1 year, 5 years, etc. Each item is produced from cars to cell phones to computers pods may have arrived DOA or a small% failure rate. There is no way to predict or quantify it. That’s why there are guarantees and lemon laws. I can look at what I have in my hands for better or worse. Contrary to popular belief, there is no special review samples of top quality. Most of my personal time to get the commercial version, sometimes I get their initial version is usually worse than the final retail version.

 

Introduction:

Manta RDA is the last Advken. They are a company that has been around for a while, but with little fanfare. Most popular products, they can gorge mad hatter GDR and with a gap on the hinge for easy filling. Manta part double coil air flow RTA with a capacity of 4.5 ml with glass bubbles (or 3 ml of capacity with ordinary glass) and is available in 5 colors, black, SS, rainbow, blue, and gold.

 

Manufacturer Specifications

Staniless 24mm stainless construction

Double gold plated curve Post and Central Bridge Section Section
Top System Re-filling
adjusting tri-water-holes System
510 wire and gold plated Pin Contact
Chubby normal standard tube spare glass and glass tubes
4.5ml / 3ml capacity According Choice tube
Coming up with a screwdriver and Confederate Bag
Standard Gift Box Package
Included in the box
1 Manta 24mm RTA
Extensions 1 Glass Bubble
1 Doctor screwdriver coil
Spare parts and O-rings

First impressions and characteristics
When I arrived this RTA I was very impressed by the performance and quality of it. A gold was only an impressive finish to it. The thread and the O-rings are really good. No O-ring sticking or damage to the glass to disassemble. air flow by using three separate holes instead of a large on each side. Ideal for people who want to lose air. It is a little tight but and it can be difficult to adjust in the mod.

Deck Construction (photos above)
Let’s talk now to build a platform. It is rather the style rhythm as in the second holes after 2 bridge by post but with more metal in it. Each lead has got the hole itself was always good and it is easy to build one. They use the hexagon socket of good quality which is my favorite. It also has some extra metal between the coils with a hole. conditioned air flow is downwards with two relatively small holes in the bottom of each coil. platform, it is very easy to align your reel on the air flow but do not have a lot of space in it. It is more suited to lower power smaller construction. I found 3 mm max be fit there and 2.5mm also works very well. Overall easy to build a platform made for a small construction

Wicking is also easy. This is a GTA-style platform is really low down. No JFC and no leakage. It was quite forgive, but you want to use a lot of cotton. Not too much throttle, but enough to fill all the slots with a cotton tip flush on the bottom. You should be able to adjust your tweezers easily between cotton and filling holes that are small enough. I found the coil 2.5mm You do not need your slim prospects at all. With the son of 3 mm reel you want to lighten a little.

success

Performance wise, I use it as a double coil RTA only as intended. I ran three building luxury coil through it in the range of 5-6 packs of 3 mm and 2.5 mm ID. I also ran 2 rounds of simple construction with 26 envelopes of measuring instruments 8-9 Nichrome 1 mm ID 3 and 1 in the 2.5mm ID. Overall, I find that it works well with everyone to build. It is quite flexible and does not need anything fancy to taste good but I would stick with either 3 mm diameter 2.5mm ID or ID of the coil. There is plenty of space for a large building, it is best to use in the range of 40-70 watts. I would not take much more than that. That said, I get a very good sense. This figure is higher than the average TSR average watts. I feel I’ve done the best construction for the taste is luxurious 5 reel film run 2.5mm ID TC 60 watts.

Overall impressions, Details and Extras
This is the bottom of the RTA and the AFC air flow is smooth, but a little tight and the cap. glass bubble, it is difficult to adjust when he was in the mod, but easy to adjust when mod. It has complete high level where you unscrew the lid and expose two large filling holes. top hat has a textured design as well and is easy to grip and open the cover. It is easy to fill all kinds of bottles or just poured juice. I used the 70/30, 80/20 and juice “max VG” in it without problem. It comes with a standard 810 point drops manta Ultem and wrote on it. It is really good and easy to disassemble with minimal parts to it. All nice and smooth thread. It is the RTA diameter of 24mm should therefore not wrong on most mods. 4.5ml capacity is quite good with a glass bubble for tanks that do not really drink juice.

pro:
manufacturing quality
visible

color selection
Tip 810 standard
build a bridge and posts good quality screws
marquee filling design
above the average for the direction RTA mid watt
4.5ml capacity
The inconvenients:
Build a platform is limited to the coil size
AFC difficult to adjust when mod
Conclusion
So with all that said, I recommend the RTA? I do not like to or not difficult, but it will lean slightly toward yes but with a caveat was added to the average VAPERS watts. If you want VAPE over 70 watts is not for you. If you want VAPE 40-70 watts and does not blow the juice and still get a good sense, it is a very good choice. It will not make my top list, but it is still good enough dam RTA. I’ll add to my list

It can be purchased here Manta 24mm TSR Advken | Staggered two Design Post at 32.95

It was Anthony fried keep only honest, I hope you can all say the same thing and I’ll catch you at the next review.

For a good recommendation please check my Google sheet located here

This sheet will be updated regularly so feel free to bookmark it.

Once again I want to thank you for sending me this elementvape.com for the purposes of this review

Also if you missed some of my past reviews you can find it here Save Me

Geekvape aegis boost review

I received boost aegis Geekvape the purpose of this review.

 

Aegis Pod System Starter Kit:

 

– Gunmetal

– Black Space

– Aura shine

– Red Devil

– blue Almighty

 

Description and features:

 

– Dimensions: 106.8 x 39.2 x 27.7mm

– Material: zinc alloy, leather and silicone

– Battery capacity: 1500mAh

– Watt Output Range: 5-40W

– Output Voltage Range: 1.0-6.0V

– Speed ​​of firing: 0.08s

– Max power: 40W

– Coil: MESH

– Charge Micro USB port

– Load current: 5V / 1.5A

– Charging Methods: easy access charge

– Air flow: easy access to the air flow valve

– waterproof, shockproof and dustproof for a long life

– 2 / 3.7ml e-juice large capacity for continuous vaping experience

– Portable Size with a sleek, minimalist design

– Fully compatible with the Pod and RDTA

– With the two coils are designed for vaping experience MTL and DTL

– stain-resistant, corrosion resistant and tear resistant

– Some of protection to safeguard a secure and stable vaping

 

 

 

 

 

In the box:

 

– improve the Aegis

– 2 x coil

– USB cable

– Coil Tool

– User’s Guide

– slippery Pointe

– to promote and guarantee card

 

GeekVape Aegis Boost Vape Pod System. Since this device is the shadow of the series, the device is resistant to water, shock and dust, building quality of this device is very good as expected. It is a device with a screen and 5-40w work. Boost is available in 5 different colors are very good. In the package, you will receive two rollers, two ends at the tip of the hat drops and drips very well. The design of this device is really good in my opinion, it is small and easy to pocket. On one side of the device you can see engraved “Geekvape squonk mod kit” and the other side you can see engraved “Aegis”.

 

So let me start with the cartridge, the device comes with a cartridge and with this unit, you can only change the coil. At the top you can see the tip of the cartridge drops in the package, you’ll receive two very good drip tips, two extreme drops in my opinion, convenient to use. These devices are not comfortable with 510 tips drops to be a drawback for some, but in my opinion, the transmission of packet drops tips to stay comfortable and enjoyable. excellent cartridge capacity of 3.7 ml, given the size of the device. In the cartridge, you can see the fill hole and fill the hole about anything in detail cans filling hole needs to take to fill the cartridge. Cartridge very well in place and the unit is not provided with a magnet. From the back of the cartridge that you can see the part you need to push to release the cartridge. On one side you can see the cartridge slot and the air flow in this device can regulate the air flow is really good.
From the bottom of the cartridge, you can change the coil and in the package, get the tools you use to remove the coil. With this tool, you can easily remove the coil and then just press on the other side. With this device receives two coils, one coil in the cartridge and the other on the package. Coils that will receive the cartridge is the driving force and power 25-33w 0.4ohm coils are recommended for this coil. The rolls were receiving coil box is a pulse with electrical resistance 0.6ohm Recommended 15-25W andd for this coil. As usual, I said to begin when the coils are used first, must be primed with a few drops of liquid E and thus prevent burns blow. This unit is compatible with the cartridge RDTA very good because you can create your own coil and save money, RDTA cartridges have not tried this, but it is a very good choice.
From the top you can see the mod slots for cartridges and connections and as I said cartridge stays perfectly in place.
This device has an integrated battery and a battery capacity of 1500mAh which is really good considering the size of this unit. On one side of the device you can see that you use the USB port to charge the battery.

On the front side of the mod, you can see the fire button, the screen and plus and minus buttons.

button fire a familiar form, it is clicky and worked well without problems. Plus and minus buttons as well and without any problems. The screen of this device is small and on the screen, we have all the information we need.

Trun on the device, you need to click 5 times on the fire button, you must do the same to turn it off. When you turn the power on screen, you can see:

 

– against Puff

– Coil Resistance

– The battery indicator

– W

 

 

To lock the plus and minus buttons you need to hold the plus and minus buttons together and you must do the same to unlock the keypad. When the keypad is locked, you can still use the fire button and you can VAPE. When you hold the fire button and the minus button you can reset the breath against.

A protective device:

 

– Over discharge

– Short Circuit Protection

– Output Current

– Protection against overload

 

 

How these devices work and my thoughts:

 

 

Thus, the shadow mod pod car is very well built, this camera is waterproof, dustproof and shockproof. build quality of this device is really good. good color choice, and in my opinion, the design of this model is really good, I really like this device looks much like another shadow mods. Aegis impulse comfortable to use and the device is small and light and therefore these devices are pocket friendly. With this device in the package you will receive two drip tips are great but it is not compatible with 510 drip tips that will con. Capacity carrtridge really good in my opinion, given the size of this unit. You can change the coil is very easy here and the great thing is that you can buy the cartridge RDTA. You can fill the cartridge without problems. cartridge holder firmly in place and you can easily remove the cartridge by pressing the back. Fire button and the plus and minus buttons either and so far all the buttons worked well. Built in battery has a capacity of 1500mAh which is good considering the size of this unit. I really like this device has a screen because you can see all the information we need.

The coil package works great, I really like 0.4ohm coil, I want to use to 26W and flavor with this coil is good enough. The device works well, there is nothing I can complain. In this device, we can regulate the air flow and excellent features airlfow you can adjust smoothly.

So I can say that the momentum can be the best auspices pod mod I have tried so far, it has everything that needs a mod pod have, is also convenient to use and the support cartridge RDTA and waterproof, dustproof and shockproof.

 

 

 

The inconvenients:

 

– It is compatible with 510 drip tips

 

 

 

 

 

pro:

 

– Good build quality

– Waterproof

– shock

– anti dust

– Choice of colors

– Two tips flowed in the package

– drip cap peak drop in package

– Two coils in the package

– Cartridge RDTA

– Capacity 3.7 ml

– the fire button and the plus and minus buttons work well

– Convenient to use

– Small and light

– Good taste

– Airflow adjustment

– No leakage

– Easy to fill

– 1500mAh

– screen

– Easy to change the coil

 

 

 

thank you Geekvape

You can buy it here: boost Aegis

Page FB: Geekvape

 

How do you vapes Burnt Tastes and make its to Fixed

Why Vape tastes burned and how to fix it
What causes burns?
When there is no liquid in the liquid core or core rod is insufficient, the atomizer diet can cause burns. No evaporation of the liquid, the coil begins to burn the fuse and the user inhales essentially burning cotton. Some of the  smok vape atomizer most common causes of burns and suggestions to help avoid these problems.

high watt
Evaporation power that exceeds the coil limit the e-liquid evaporates too quickly. When this happens, the coil can burn the wick, even if there is no juice. Always stay within the recommended power margins.

Quick Links:Morph 219W kit ,RPM40 Kit, Smok MAG P3

suck chain
A continuous inhalation the wick dries quickly. If you notice a slight smell of toast and the feeling that comes a candy smell, please temporarily put the vaporizer. This will allow the liquid to cover the tip of the wick dried.

The high use VG E-Liquid Smok novo 2
Not all spray atomization is the same. Some spray storage tanks can contain high VG juice while other storage tanks usually require a PG or PG than 50% in order to function properly. A good rule of practice is to check the size of the wick channel. If the hole diameter is small, the water tank can not be well suited to the high TB ​​juice.

Bobbin is well oiled
This is probably the most common problem in the list. irrigation head coil is essentially the wicks dipping process with e-liquid, so they are ready for first use. If you want to avoid burns, always remember infuse the spool properly.

Install the coil: the stop combustion
Although the idea is the same, the coil boot process varies depending on the equipment used. These are some of the most commonly used methods of vape infusion.

How freezer coil first reservoir
All tanks with coil Vape replaceable heads have roughly the same structure and the same simple steps needed to boot. This process must be repeated each time the coil is replaced.

Quick Links:TFV16 Mesh Coil ,TFV16 Dual Mesh Coil, TFV8 Pyrex Glass Tube

New coil outlet box
E-drop of the liquid in the drill hole and the coil head (3-4 drops are sufficient)
Fit the water tank and pour the juice RPM2 Kit
Screw your tank in the Ministry of Defense and let stand for 10 minutes
Inhalation fuel tank top without ignition accelerate the process of
Vape for mods with power adjustment function, you must start with the lowest recommended power and increase gradually to find the best position
Note that as more liquid can accumulate inside the coil, you may experience some regurgitation during the first aspiration. Do not go, and you use a variable power module, try to increase the power a few times, but make sure not to exceed the power limit of the coil because it is likely to burn.

SCAR 18 SMOK REVIEW – WHAT’S DO YOU THINKS?

Recently, we had a full review of the new series of SMOK Cicatriz-P3 and P5 Scar Kit, now look a shot at another new member of this series scar, the scar SMOK 18.

smok vape

As vaporizer kit sheath system has been popular for a long time, now is the turn of the powerful of the box set!

So you can get 18 SMOK scar?

1 x 18 Scar-Mod
1 x deposit TFV9 (6.5 ml)
1 x coil V9 0.15ohm mesh (pre-installed)
1 x V9 mesh Coil 0.15ohm
1 x replacement glass tube
1 x USB cable
1 x User Manual

IP67 dustproof and shockproof and

RPM40 Kit

18 SCAR waterproof IP67 which can withstand water immersion between 15 cm and 1 meter for 30 minutes. It is also dustproof (IP67) and shock-proof to avoid dust and accidental falls.

Always adhere to the water test kits Geekvape water? Now, maybe you should take a look at SMOK! Anyway, if you’re a fan of the outdoors, this IP67 resistant to water and dust test kit and anti-shock SMOK Cicatriz 18 is definitely your best choice!

Sabor advance -TFV9 tank

RPM2 Kit

New TFV9 tank comes with two coils mesh V9 0.15Ω which are designed for sub-ohm vaping for hunters cloud.

510 thread connector

TFV9 tank uses a fixed spindle to increase the frictional resistance of the year increases the electrical conductivity, so that the connector can retain its original appearance, even if reused. Moreover, you can get the best user experience for connecting the tank with a mod.

Capacity 6.5ml e-juice

No need to fill the juice often to ensure your pleasure and vaping.

Top loading system

TFV9 the reservoir includes a slidable filling system for simple e-liquid refills and safety. narrow slit can significantly solve leakage problem.

V9 mesh 0.15Ω Coil

Smok novo 2

V9 mesh Nichrome coil that has a large heating surface for producing huge clouds and superb flavor with less time to heat.

The full range of baby V8 coils (for the standard version will come out of the EU) are compatible with the EU TFV9 TFV9 tank and the tank.

Childproof top cap for increased security

Quick Links:TFV16 Mesh Coil ,TFV16 Dual Mesh Coil, TFV8 Pyrex Glass Tube

The top cover of the locking mechanism adopts lifting method and open to keep children away from the tank. The design can also effectively prevent accidental opening of the upper capsule and the fluid leak-e.

Scar 18 powerful Mod

Lighting new possibilities mod box, SCAR 18 becomes synonymous with power and performance.

It is driven by the latest IQ-X chipset with stable production and exceptional efficiency, and uses two 18650 batteries provide a maximum power of 230W to provide your vaping experience powerful and long lasting.

LOST VAPE TANKS

Main Features:

compact design, powerful and portable
IP67 waterproof, shock and dustproof
Powered by two external batteries 18650
IQ Intelligent integrated-X chipset
output power 230W
Support the precise control of the temperature of nickel, titanium and stainless steel
6.5ml e-liquid large capacity
Slide-to-fill system
Childproof top cap for increased security
V9 mesh coil produce huge clouds and superb flavor
Gold plating connector 510 wire
Multiple protection: intelligent disconnection Atomizer Recognition / Puff Monitoring System / 8 Seconds / protection of short-circuit / protection against overheating / Low battery warning

Read more below:

SMOK 18 Scar Kit

Double 18650 Mod Pod SMOK RPM 160 VS artery pepita GT, wherein?

SMOK artery and double sheath 18650 mod out for great power and long vaping times.Do innovative design you like? What ‘s the difference between the double SMOK RPM160 Mod Pod Kit 18650 and 18650 double nugget artery GT Mod Pod Kit? Let ‘s check boards!

Double RPM160 1.SMOK 18650 Mod Pod Kit

Smok RPM160 double kit Mod Pod 18650 is the first and largest battery mod Smok two sheaths. It’s a bit bigger than other PMP devices, the most powerful version of the pod systems like Smok Smok previous Smok RPM40 RPM80

and RPMLite.smok vape atomizer

Smok RPM160 many beautiful colors of carbon fiber: black, blue, red, silver, gold and rainbow.
Smok RPM160 Mod Pod Kit is powered by a battery with a dual power 160W max 18650. Pod RPM160 Smok kit includes a new set of IQ-160 chips and a TFT vaping 0.96 inch display data clearly. Smok RPM160 cartridge is provided with a capacity of 5 ml with filling high design. Furthermore, the type C rapid charging system allows fully charged battery in a short time.

The Smok RPM160 have the option of using two different RPM Pod and CER. RPM Pod is compatible with all RPM coils. Pod RGC is the first design Smok sheath with adjustable airflow. the use of the new cartridge is recommended with conical coil RGC networks. This head nexMesh using technology to produce a strong gust of wind hit the throat and lots of exceptional taste. This is the last frame of system high watt ultra-portable mod / pod one.

Quick Links:TFV16 Mesh Coil ,TFV16 Dual Mesh Coil, TFV8 Pyrex Glass Tube

features:
1. First and foremost dual battery Mod Pod SM0K
2. 18650 Powered by dual with 160W Max output
3. New IQ-160 chipset
4. RPM80 RGC Pod with adjustable airflow design
5. RPM80 RPM Pod – Compatible with other coils RPM
6. intelligent recognition sprayers
7. Monitoring System blow
8. New RGC cone coupling coil
9. 5 ml capacity filled design Top
10 multifunctional protection.
11. 0.96 inch TFT
12. Cutting 10s

Double RPM160 1.SMOK 18650 Mod Pod Kit

Smok RPM160 double kit Mod Pod 18650 is the first and largest battery mod Smok two sheaths. It’s a bit bigger than other PMP devices, the most powerful version of the above systems like Smok Smok sheath of RPM40

RPM80 and RPM Lite.RPM40 Kit 

Smok RPM160 many beautiful colors of carbon fiber: black, blue, red, silver, gold and rainbow.
Smok RPM160 Mod Pod Kit is powered by a battery with a dual power 160W max 18650. Pod RPM160 Smok kit includes a new set of IQ-160 chips and a TFT vaping 0.96 inch display data clearly. Smok RPM160 cartridge is provided with a capacity of 5 ml with filling high design. Furthermore, the type C rapid charging system allows fully charged battery in a short time.

The Smok RPM160 have the option of using two different RPM Pod and CER. RPM Pod is compatible with all RPM coils. Pod RGC is the first design Smok sheath with adjustable airflow. the use of the new cartridge is recommended with conical coil RGC networks. This head nexMesh using technology to produce a strong gust of wind hit the throat and lots of exceptional taste. This is the last area of ​​high ultraportable watt mod / pod systemall

one.Morph 219W kit 

Quick Links:RPM2 Kit ,Smok novo 2

features:
1. First and foremost dual battery Mod Pod SM0K
2. 18650 Powered by dual with 160W Max output
3. New IQ-160 chipset
4. RPM80 RGC Pod with adjustable airflow design
5. RPM80 RPM Pod – Compatible with other coils RPM
6. intelligent recognition sprayers
7. Monitoring System blow
8. New RGC cone coupling coil
9. 5 ml capacity filled design Top
10 multifunctional protection.
11. 0.96 inch TFT
12. Cutting 10s

2.Artery pome 18650 GT Mod Pod Kit double
Kit nugget GT artery is the first double world Mod Pod Kit 18650, which is powered by a battery with a power of 200W dual 18650 max. Pome chip arterial sheath GT Aero Kit comes with a constant power and multiple protection. Nugget artery GT adopts color display .96 inches and cool LEDs.artery Nugget Smok MAG P3

RTA and tank sub-Ohm

From the perspective RTA and tank sub-Ohm exterior view, RTA and tank sub-Ohm looks very similar and difficult to distinguish. But the biggest difference in it, and a significant difference between the two are. Under Ohm tank is easy to recognize because the coil is replaced and the assembly to clear. On the other side of the RTA building platform can be complex, so beginners can not be confused with intricate designs and patterns. They all have their own advantages and disadvantages, and it is to decide the electronic cigarette atomizer which to use. Let’s look at the tank RTA and sub-ohm and see which one is best for your service is vaping.

Quick Links:SCAR-18 Kit,SMOK SCAR-P3,Scar P5 kit

RTA higher if the search for a delicious taste. I can not underestimate the sub-ohms and its ability to produce flavor, but all in all, the outbound direction RTA exceed many sub-ohm doses. crooked with the ability to hand a role to fulfill, the RTA can adjust the ambitious helix structures that never appear in a prefabricated replacement coils so that the end or flavors clouds that can be customized according to user preferences. RTA has a platform that can really take a single coil or dual-coil configuration and a special air flow path that one or more coils acts to pull the tongue and lungs evaporate eJuice. In addition, the central air flows prefabricated coil used in sub-Ohm tank LOST VAPE vertically passing through the coil, so more is absorbed aroma half of the coil is exposed, while the other half remained in contact with means cotton wick suction. In addition to,

Both RTA and the storage tank sub-Ohm has a large capacity, particularly when the glass bubbles are introduced. Depending on the selected storage tank or RTA, the maximum capacity of more than 4 could reach ml. Thereby, the amount of filling of the reservoir can reduce output sub-ohm or RTA before bubbles is introduced into the glass container. The important difference between the two is that the major part ohm of the fuel tank under an air flow control system have, in the bottom of the tank is arranged, as the wick system depends on the pieces, which are blocked by the pieces of cotton wick that which blocks most of the electrical potential leaks leading to the center of the coil. However, the RTA tilts the control system to keep the air flow to prevent such potential leakage problems for them, because the RTA must be the wrong hands, allowing users to more or less cotton use to slow down the rate of wicking or accelerate.

Quick Links:SMOK Novo X Kit ,smok nfix kit

RTA is usually more expensive than the tank sub-ohms, but this is usually at the cost of repairable atomizer tank and coil construction material. In the case of RTA, since the coil by hand, which can be produced in a coil of wire at a fraction of the cost of replacement coils so that the number of coils that can be provided over a packet replacement provision. However, the money saved would be a waste of time. much time and effort coils replace RTA is needed. In this case, the deposit sub-Ohm wins because the tank can only pull or loosen the coils used and replace it with a new reel in less than a minute a variable coil and users. After the RTA decided that the coils can be replaced, take the time, the old coil and build and install a new role to remove. This process can easily 10 minutes or more.smok vape